收藏本站
3.5- and 4.5-Digit, Single-Chip
ADCs with LCD Drivers
If ghosting is present on the LCD, the RMS OFF voltage
is too high. Choose an LCD with a higher RMS OFF
voltage or decrease DV DD .
Decimal Point Control
The MAX1491/MAX1493/MAX1495 allow for full deci-
mal-point control and feature leading-zero suppression.
Use DPON, DPSET1, and DPSET2 to set the value of
the decimal point. Tables 2 and 3 show the truth tables
of the DPON, DPSET1, and DPSET2 that determine
which decimal point is used.
Reference
The MAX1491/MAX1493/MAX1495 reference sets the
full-scale range of the ADC transfer function. With a
nominal 2.048V reference, the ADC full-scale range is
±2V with RANGE equal to GND. With RANGE equal to
DV DD , the full-scale range is ±200mV. A decreased ref-
erence voltage decreases full-scale range (see the
Transfer Functions section).
The MAX1491/MAX1493/MAX1495 accept either an
external reference or an internal reference. The INTREF
input selects the reference mode.
For internal reference operation, connect INTREF to
DV DD , connect REF- to GND, and bypass REF+ to
GND with a 4.7μF capacitor. The internal reference pro-
vides a nominal 2.048V source between REF+ and
GND. The internal reference temperature coefficient is
typically 40ppm/°C.
Connect INTREF to GND to use the external reference.
The external reference inputs, REF+ and REF-, are fully
differential. For a valid external reference input, V REF+
must be greater than V REF- . Bypass REF+ and REF-
with a 0.1μF or greater capacitor to GND in external ref-
erence mode.
Figure 13 shows the MAX1493/MAX1495 operating with
an external differential reference. In this mode, REF- is
connected to the top of the strain gauge and REF+ is
connected to the midpoint of the resistor-divider on the
supply.
Applications Information
Power-On
At power-on, the digital filter and modulator circuits
reset. The MAX1493/MAX1495 allow 6s for the refer-
ence to stabilize before performing enhanced offset
calibration. During these 6s, the MAX1493/MAX1495
display 1.2V to 1.5V when a stable reference is detect-
ed. If a valid reference is not found, the MAX1493/
MAX1495 time out after 6s and begin enhanced offset
calibration. Enhanced offset calibration typically lasts
2s. The MAX1493/MAX1495 begin converting after
enhanced offset calibration.
Offset Calibration
The MAX1491/MAX1493/MAX1495 offer on-chip offset
calibration. The MAX1491/MAX1493/MAX1495 calibrate
offset during every conversion cycle. The MAX1495
Table 2. Decimal-Point Control Table (MAX1493/MAX1495)
DPON
0
0
0
0
1
1
1
1
DPSET1
0
0
1
1
0
0
1
1
DPSET2
0
1
0
1
0
1
0
1
DISPLAY OUTPUT
18888
18888
18888
18888
1 8 8 8.8
1 8 8.8 8
1 8.8 8 8
1.8 8 8 8
ZERO INPUT READING
0
0
0
0
0.0
0.00
0.000
0.0000
Table 3. Decimal-Point Control Table (MAX1491)
DPSET1
0
0
1
1
DPSET2
0
1
0
1
DISPLAY OUTPUT
1 8 8.8
1 8.8 8
1.8 8 8
1888
ZERO INPUT READING
0.0
0.00
0.000
000
______________________________________________________________________________________
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX16031EVKIT+ KIT EVALUATION FOR MAX1603
MAX16050EVKIT+ EVAL KIT FOR MAX16050
MAX16929EVKIT+ KIT EVALUATION FOR MAX16929
MAX16946EVKIT+ KIT EVALUATION FOR MAX16946
MAX17015EVKIT+ KIT EVAL FOR MAX17015
MAX17021EVKIT+ EVAL KIT FOR MAX17021
MAX1702EVKIT EVAL KIT FOR MAX1702
MAX17710EVKIT# RD ENERGY HARVESTING
相关代理商/技术参数
MAX1494CCJ 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1494CCJ+ 功能描述:模数转换器 - ADC 4.5 Digit ADC w/LCD Drivers RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1494CCJ+T 功能描述:模数转换器 - ADC 4.5 Digit ADC w/LCD Drivers RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1494CCJ-T 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1494EVC16 功能描述:模数转换器 - ADC MAX1494C16 EVAL KIT RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MAX1494EVKIT 功能描述:数据转换 IC 开发工具 Evaluation Kit/Evaluation System for the MAX1493 MAX1494 MAX1495 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
MAX14950ACTL+ 功能描述:外围驱动器与原件 - PCI PCIe Gen III Re-Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
MAX14950ACTL+T 功能描述:外围驱动器与原件 - PCI PCIe Gen III Re-Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray